Numerical investigation on flow nonuniformity-induced hysteresis in scramjet isolator

Numerical simulation and theoretical analysis were conducted to study the hysteresis inside scramjet isolator during the reciprocating process of back pressure variation. It is revealed that only a regular reflection is theoretically possible for two leading shocks when the inflow Mach number is greater than 2.0, and no hysteresis can occur in the transition between shock reflection types. Nevertheless, wall suction, gas injection, and background waves cause non-uniformity of the incoming flow and would make hysteresis possible. Besides the classical hysteresis in the transition between shock reflection, new kinds of hysteresis were found in both the deflection angle of separated boundary layer and the location of the shock train. Moreover, the occurrence of hysteresis in the deflection angle of the separated boundary layer is accompanied with the shock reflection hysteresis. In the case with background waves or gas injection, hysteresis in the starting position of leading shock was observed too. As back pressure decreases, the leading shock does not follow the same path as that as the back pressure increases, and it is anchored at the location where the background shock or the injection interacts with the leading shock. It is inferred that, if two strong adverse pressure gradient regions move towards and interact with each other, hysteresis will take place when they start to separate.     

失重性骨质疏松腰椎力学性能研究

航天员在长期失重环境影响下,会容易造成椎体失重性骨质疏松。为了探究骨质流失对腰椎承载能力的影响,设计了不同骨密度的腰椎力学仿真,通过图像处理建立了腰椎三维模型,利用有限元算法得到腰椎应力分布,对比了不同材料属性腰椎模型应力结果。结果表明:骨质疏松腰椎的应力值较正常腰椎变小,而形变量却明显增大。可以看出,骨质流失时,会导致腰椎骨骼材料性能发生变化,使腰椎形变量增大,并且使腰椎结构承载能力降低。     

静压气浮轴承工程设计方法研究

静压气浮轴承是惯性器件测试平台回转支撑轴系的关键部件，其承载能力和回转精度对惯性器件测试的准确性有着重要的影响，目前，静压气浮轴承设计、计算过程复杂，为提高设计效率，简化设计方法，在满足静压气浮轴承性能的条件下，推导了静压气浮轴承工程计算公式，在此基础上，设计了一款双向止推空气轴承，确定了几何参数，计算了空气静压径向轴承、空气静压止推轴承的轴承承载力、刚度、耗气量及摩擦力矩，并与有限元仿真结果进行了对比分析，验证了该设计方法的有效性。     

Fast spacecraft solar radiation pressure modeling by ray tracing on graphics processing unit

A novel method is presented to evaluate on the graphics processing unit (GPU) the force and torque on a spacecraft due to solar radiation pressure. The method employs efficient ray tracing techniques, developed in the graphics rendering discipline, to resolve spacecraft self-shadowing and reflections at faster than real-time computation speed. The primary algorithmic components of the ray tracing process which contribute to the method’s computational efficiency are described. These components include two-level bounding volume hierarchy acceleration data structures, fast ray to bounding box intersection testing using the slab intersection algorithm and fast triangle intersection testing using the Möller-Trumbore algorithm. Spacecraft material optical properties are represented as a combination of Lambertian diffuse and ideal specular reflections. Both diffuse and specular ray-surface interactions are modeled. The approach is implemented using C++ and OpenCL and executed on a consumer grade GPU. Model validation is presented comparing ray traced force and torque values to the same quantities produce by a faceted analytic model. Numerical results illustrate the impact of self-shadowing on the force and torque calculation, and demonstrate the fast computational speed that is enabled with this implementation.     

基于功能脆弱性的空中交通相依网络流量分配

依据空中交通管理与航班运行规则,采用复杂网络理论构建由机场、航路与管制扇区组成的相依网络模型,建立不同扰动策略的影响规则,提出以网络流量熵和交通流损失比变化率为指标识别网络功能脆弱性。并以网络总流量熵最小为目标,建立基于改进遗传算法的网络流量协调分配策略,以降低空中交通相依网络的脆弱性。以民航华北地区空域为原型,发现了其相依网络脆弱性表现规律和脆弱源,采用遗传算法求解网络流量分配方案,优化结果降低了网络总熵值和功能脆弱性,其中机场网络流量分配后效果最为显著,验证了方法的有效性,研究结果可为空中流量管理决策提供一定的理论支撑。     

主流攻角对双射流孔气膜冷却特性的影响

应用压力敏感漆技术,在平板上测量了不同主流攻角(i=-30°,-20°,-10°,0°,10°,20°,30°)下双射流孔的气膜冷却效率,并利用计算流体动力学(CFD)计算得到的流场对气膜冷却效率的规律进行了解析。所研究的双射流孔结构的孔间无量纲横向距离为0.5,孔间无量纲流向距离为3;射流与主流密度比为1.0,吹风比分别为0.5、1.0、1.5、2.0。结果表明小的主流攻角(i=-10°,0°,10°)下,流场中存在反肾型涡对或挤压作用,气膜层与壁面贴附良好,气膜冷却效率最高;大正值攻角(i=20°,30°)下,虽然气膜覆盖面积大,但反肾型涡对退化,气膜冷却效率下降;大负值攻角(i=-20°,-30°)下,流场中有肾型涡对,且气膜横向覆盖受限,气膜冷却效率最低。     

盘腔进气位置对径向预旋系统的影响

为减少径向预旋系统的流动损失,运用数值模拟方法对不同盘腔进气位置的径向预旋系统进行分析,结果表明:随着盘腔进气径向位置的增加,预旋喷嘴出口气流旋流比随之逐渐减小,径向预旋系统的温降系数及总压损失系数均随之逐渐增大。当旋转雷诺数等于7.9×106,盘腔进气位置由低位向高位变化时温降系数最大可增加525%,同时总压损失系数增加3.93%。径向预旋系统内比熵增主要发生在预旋喷嘴和共转腔,约占系统总体比熵增的80%。随着盘腔进气径向位置的增加,径向预旋系统总体比熵增降低,预旋喷嘴比熵增占比逐渐增大,共转腔比熵增占比逐渐减小。     

极低压下两相流挤压油膜阻尼器油膜参数特性

针对极低供油压力工况开展实验研究,以考察气液两相流对挤压油膜阻尼器(SFD)油膜参数特性的影响。结果表明:当SFD入口气体体积分数小于0.9时,油膜阻尼随着入口气体体积分数的增加而减小,直至气体体积分数增大到0.9时,油膜阻尼是纯油状态时阻尼的60%;当气体体积分数大于0.9时,油膜阻尼大幅减小至几乎可以忽略不计。现有理论模型并不适用于极低供油压力工况。基于实验结果,找到了最符合SFD两相流动的等效黏度模型,其理论预测的油膜阻尼与不同供油压力下的实验数据吻合较好,为SFD两相流研究的模型选择提供了依据。     

展向振荡对激波/湍流边界层干扰的影响

周期振荡作为一种有效的壁面流动控制手段受到广泛关注,而其对激波/湍流边界层干扰的影响目前鲜有研究。本文采用高精度直接数值模拟（DNS）方法对马赫数2.9、12°激波入射角、强振荡下的激波/湍流边界层干扰进行了系统研究。通过与无振荡工况的定量比较,揭示了展向强振荡对干扰区内复杂流动结构的影响规律及作用机制,如分离泡尺度、物面压力脉动非定常特性、物面剪切的非定常特性及统计特征等。研究发现：在展向强振荡作用下,分离点位置提前,间歇区长度增大;同时由于分离泡内强黏性耗散的影响,展向振荡的穿透高度约为分离泡高度的4%,因而对流动结构不会产生实质影响。但展向强振荡会对壁面附近流动造成显著影响,如强振荡诱导的壁面展向速度远大于流向速度,造成流向剪切与展向剪切之间夹角的概率密度函数峰值从0°偏移到80°~90°之间。物面压力及剪切本征正交分解分析表明,展向振荡会导致模态能量从低阶模态向高阶模态转移,降低低频运动的能量占比,增强再附后Görtler涡等壁面附近旋涡结构的强度。     

高超声速钝头体边界层转捩试验

为研究高超声钝头体边界层转捩以及头部钝度对转捩的影响,在FD-14和FD-14A两座激波风洞中开展了热流、压力扰动和高速纹影显示等综合测量。试验结果表明,转捩雷诺数关于钝度雷诺数的变化显示出转捩反转的趋势。压力扰动的功率谱密度（PSD）分析结果以流向离散分布云图形式显示,边界层高速纹影图像显示了第二模态波的发展、湍流的生成和熵层对边界层结构的显著影响。大头部钝度带来的强熵梯度熵层流动对边界层压力扰动频谱特性和流动结构影响显著,在转捩反转机理中起到重要作用。此外,马赫数对转捩的影响不容忽视。